Nov 19, 2026

I recently installed two solar panels on my balcony. This is thanks to California's new "balcony solar" law, SB 868, which lets you plug a small set of solar panels directly into an ordinary outlet on your house. DIY: No electrician or permit required. The panels just feed power back into the house through the same kind of outlet you'd plug a lamp into.
I should admit up front that my install is technically in a bit of a gray area when it comes to the law's requirements, but more on that below.
The installation was pretty simple. It took me about an hour, and the only hardware required was some heavy duty zip ties, which came in the box with the panels.

It's a little early to draw conclusions, since it's been cloudy and rainy ever since I put them up. Still, I've generated over a kWh on my best day so far, and I've seen over 250W of power coming in at peak.
SB 868 was signed at the end of September and officially takes effect on January 1, 2027, so yes, I'm also a few weeks early. The short version: a plug-in solar system of up to 1,200W no longer needs an interconnection agreement with your utility, and the utility can't charge you fees for it. Before this, even a single panel was treated like a full rooftop system on paper. This kind of setup has been common in Germany for years, where it's called Balkonkraftwerk, or "balcony power plant".
The catch is that the system has to be certified as a plug-in solar system by UL or an equivalent lab. In practice that means a new standard called UL 3700, and that's where my gray area comes from. As I understand it, UL 3700 wants two things that I don't have: a special outlet and a dedicated circuit.
UL 3700 calls for a unique plug and matching receptacle that won't mate with a normal household outlet. The reason is what UL calls touch safety. A normal plug is only ever on the receiving end of power, so its metal blades are dead the moment you pull it out of the wall. A solar panel's plug is different, because the power is coming from the cord. If the plug is loose or gets pulled partway out, the exposed blades can stay energized. An inverter does notice that the grid has gone away and shuts itself off, but the general rule allows it up to two seconds to do so, which is a long time to be touching a live plug. My inverter, a Hoymiles HMS-360-1WM-LV, is reportedly quicker than that, dropping to under 34V within a second of being unplugged.

That slide is from a UL Solutions presentation that walks through the reasoning, and Bright Saver has a more readable explainer: Why does a fully certified plug-in solar kit need a special outlet?
Here's the funny part. As far as I can tell, this special outlet and plug don't exist yet. I couldn't find one for sale anywhere, or even a picture of one. So technically there's no way to satisfy this requirement right now, even if you wanted to.
In the meantime, I feel comfortable with my installation. The panels are plugged into a GFCI outlet, and that outlet lives inside a heavy duty outdoor outlet box. The cover closes over the plug, so nothing is going to bump it loose, and nobody is going to brush against the blades by accident.

A breaker only sees the current flowing through it from the breaker box. If solar is feeding the same circuit from the other end, the wiring in the wall could carry more than the breaker's limit without the breaker ever noticing.
My circuit isn't technically dedicated, but nothing else is plugged into it, and I'd unplug the panels before adding anything. It's also a 20A circuit, and my inverter's rated output tops out at 3A, so the panels can't add much even on their best day. The worst case is that the wiring ends up carrying 23A before the breaker trips, instead of 20A. To get there, I'd need other things on the circuit drawing more than 20A at the same moment the panels are at full output. And since the outlets on this circuit are all 15A outlets, no single appliance should be able to do that on its own unless it's broken. Realistically it would take two heavy loads running at once, in full sun, on a circuit where I currently have nothing else plugged in. Still, "I promise to be careful" is not the same thing as meeting the standard, so: gray area.
I bought my system from Bright Saver, a nonprofit that advocates for plug-in solar in the US. They're the same folks behind the special outlet explainer above. Along with the policy work, they sell balcony solar kits to their members at roughly what the kits cost them. Membership is $29 a year.
I went with the Flex 360 kit, which is the two panel option. In the box:
My total with taxes came to $455, which works out to about $1.26 per watt. There's also a single panel version of the kit if you have less railing to work with.
The inverter connects to wifi and reports to Hoymiles' S-Miles Home app, which is how I know any of the numbers in this post. It shows how much power the panels are producing right now, the total for today, and a lifetime total, along with a chart of each day's production.

This screenshot is from around lunchtime on a cloudy day: 191W coming in, 414Wh so far that day, and 8.92kWh since I plugged the panels in.
S-Miles also has a cloud integration for Home Assistant, so I've been pulling the same data into HA as well.
I only have a few cloudy weeks of real data, so for a full year I asked PVWatts, the national lab's solar calculator. I told it I have 360W of panels in San Jose, facing south and hanging straight up and down, with nothing shading them. It estimates about 365kWh per year. That works out to about 1kWh per day on average, which is in the same ballpark as what I've seen on my better days so far.
Vertical is a much worse angle than a tilted rooftop panel gets, but it has one funny side effect: the panels do their best work in fall and winter, when the sun is low in the sky and shining straight at them. PVWatts expects more than twice as much from them in October as in June.
My power comes from San Jose Clean Energy and is delivered by PG&E. Between the two of them I pay roughly 40 cents per kWh, so:
Nobody is getting rich on $145 a year. But for an hour of work and some zip ties, I'll take a three year payback.